Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
On this page below you will discover a lot of amazing material with regards to Installing A Bathtub.
Mounting a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old tub is easily available, the project can relocate rapidly; if you have to open up a wall to remove the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and embeded in the new one. See to it you have certified yourself for the job and are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might require a specialist plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your washroom if you have actually currently acquired a brand-new tub and don't need to transform the setup of your previous water pipelines.
Your tools and product checklist should consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. Once the supply pipes have actually been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, place the tub in the called for position. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the bathtub as well as additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub ought to wait until the bath tub has actually been utilized a minimum of when as this will resolve it into its last setting.
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, resulting in issues with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking a few minutes to read through our article post. Sharing is caring. You just don't know, you may be doing someone a favor. We treasure reading our article about Installing A Bathtub.
Request our emergency plumbing support. Report this page